The new v1.6 CEOSD, 100A current sensor, support ChainLinkDare Rx now

Customed for BEVRC. The V1.5 have some differences in PCB, but you just need to pay attention to the marks of the PCB, you can connect them right.

Defination of the marks on the main board PCB:

GPS: connected to the GSP with the cable

KEY:connected to the reset button.

SEV: connected to one spare channel of your radio receiver to swith the screen of the OSD showing

TX: reserved

RSSI: connected to your analog RSSI, to show the volt of RSSI.

AV OUT: connected to your video transmitter

AV IN: connected to your video camera

SENSOR:connected to the current sensor

BAT:connected to a battery which power your video devices

PINS with Jumper: to choose the power source

The newest version of CEOSD, switch-mode power and Imperial unit support.

 How to swith units?

Press the reset button for a while, the unit will change.

Includes:

1* OSD main board

1* 10hz GPS with cable

1*100A current sensor

some leads.

Manual download: Manual

Feature:

CEOSD is featured in small dimension, light weight and plug & play. This OSD
is fully automatic without any manual setup; it adapts to 5 or 10 Hz GPS as well as PAL and NTSC video signal input. RSSI (receiver signal strength identification) is also realized on this tiny OSD.

U can switch between 2 interfaces during your flight using one of your radio channel.

one is radar, and one is blank(looks like u turn off your OSD), see the pic below.

Power jumper: connect 1 and 2 to power up OSD and wireless video equipments with
additional 12V power supply; connect 2 and 3 to power up OSD and wireless video
equipments with plane�s 3S (11.1V )power battery.

User guide
Connect the equipments as above, power it on, and OSD shows start-up screen as
below:

After several seconds:

As GPS beginning to search satellites, the satellite number is indicated by the
GPS strength icon on the upper right corner. A flashing icon indicates weak or
unreliable GPS strength and take-off in this situation is not recommended.(with good
GPS signal, the satellite searching would last 1-5 minutes depending on different
circumstances). The status LED on the main board will begin to flash after enough
and reliable GPS signal is maintained; meanwhile, the OSD timer starts to count,
which refreshes at the same frequency of GPS (5HZ, 10HZ).
Note: CEOSD detects the working frequency of GPS and automatically matches it at start-up.

Important Considerations
1. Before taking off, in case the readings are not correct, press reset button to
reset all parameters. (This operation will reset altitude, distance, timer, current
and mAh consumed).
2.When OSD detect 0 voltage on the power battery, it will not display voltage, current
and mAh consumed of power battery.
3. Return to Home:
The �H� on the screen indicates �Home�, when the home is in front of the plane,
H will not flash; when home is behind the plane, H will flash; When H is in the middle
and not flash, it indicates the plane is heading directly to home; When the H is
in the middle and flash, it indicates the plane is flying 180 degree away from home;
How to return to home: when H is on the left ,turn left; when the h is on the right,
then turn right.
4.CEOSD will automatically detect video signal input and support both PAL and
NSTC signal.
5.CEOSD heats up during working, which is normal.

RSSI voltage display
CEOSD can display RSSI voltage
RSSI voltage measuring range: 0.1�3.3V, when this voltage is below 0.1v, OSD will
not display this parameter.
How to use:
Soldering two wires as indicated below to the RSSI port on the receiver. In case
the OSD display switching cable is already connected with the receiver, only connect
a RSSI voltage wire to the OSD, duplicated ground cable is not necessary.

Note: In order to display RSSI voltage, the user has to open the receiver and to solder wires
by himself and bears all consequent damage due to this operation.

CEOSD(Cyclops Easy OSD) Test 1 from BEVRC on Vimeo.

CEOSD test 2 from BEVRC on Vimeo.

Skywater + CEOSD + the moon from Bernhart Dambacher on Vimeo.

 osd, December 11, 2011

Fantastic it works !, plug and play, the only thing is to keep the gps module away from the camera and electronics or sometime it wont lock on the satellites, a friend has a usb cable to modify the information on the screen any idea where i can get this ?.

 Great OSD, November 29, 2011

I just powered up my OSD today. Special thanks to Alvaro who has sent me special instructions video for TX, Current Sensor and Camera connections. It took 1-2 hours to finish all soldering and see the system working. I can\'t wait to test it on this weekend!

 CE OSD, November 18, 2011

just wanted to say this product is awesome.... does everything you want from a OSD and more.. simple and works out of the box... only complaint is the manual.... totally not up to date..... also screen shots on the manual is not the same as on the new product 1.5 also no support on how to set the dipp switch and also no info on how to solder the wires to support 2 batt.... so if you need help let me know as i have it 100%.... at the end a awesome product for the price...

 ceosd, November 12, 2011

real good osd a little crapy instruction but got to work out how everything was to be connected, if anyone has any doubts don\'t hesitate contacting me on alvarituti@hotmail.com because bevrc support isn\'t really good in my opinion

 Info needed, November 9, 2011

I have ordered the osd but need help with wiring... can anybody provide me with more relevant info as the instructions are not that clear on how to mount 2 batt and where to mount the 2nd bat for video and dip switch

 Super osd simple et efficace, October 14, 2011

J\'ai reçu trés vite 10 jours ( france ), montage facile en 20 min et trés bon rendu d\'affichage, bien lisible et trés simple juste ce qu\'il faut trés bon produit

 ce osd review, September 24, 2011

This is a great osd. It has the basics and that is all I wanted and need. I lost oriantation one time and was lost. With the return to home arrow it was just as simple as pointing it home and I was back. When you see Max at the end of a flight that is you maximun of your height and distances you have flown. Just have to press reset and off you go. You can\'t beat the price, I know I love mine. For the plugs I put a drop of hot glue on them so the do not come loose inflight. Better safe then sorry. Alex Montreal,Canada

 great osd gps , September 11, 2011

just i\'m very happy with cyclops so great working... and for fast shipping thank you bevrc , we liked you ;)

 CE OSD, July 24, 2011

This is the first osd i have setup and it was really easy , it took around 20 mins and that included soldering the connectors to the voltage sensor. Screen display is great and simple. going to order my second one now

 bateria de 4S e bateria de 3S, July 17, 2011

posso usar uma bateria de 4S para o avião , e uma bateria de 3S para o sistema FPV ? bateria 4S passando pelo sensor de corrente ------ bateria de 3S alimentando a placa-------- obrigado! Celso

 CE OSD, June 11, 2011

Today I had my FPV maiden. Well it is so great. I can recomend everybody this OSD. It works good, and it displays everything you want to know during flight. At the end you see all the max\'s. I\'m used it with the Bev 5.8Ghz 500mW system, it\'s a very good combo.I\'m glad to be the owner of these systems.

 CE OSD v1.5, June 9, 2011

I received in 10 days (Brazil) my CE OSD. It came in perfect condition and in version 1.5 which looks like the HUD of an F-16, I loved the new version. Answering the review below, appears the MAX indication because the velocity and height are zero, in flight will not have this message.

 CE-OSD, June 7, 2011

Today I recieved the CE-OSD. Shipping takes 1 week. The Osd looks great. If start up it says it is version 1.5 ??? After a test of a 20 minutes I got a message in the screen says MAX. Don\'t know what that is. Try to make a maiden FPV tomorrow.

 CE OSD v1.3, May 16, 2011

Good pricing and service from BEVRC, shipping was very fast. The OSD is great for the money, easy to install and use.

 CE OSD V1.3, May 5, 2011

No setup to be done. It really is plug and play. Reset button is a great idea and GPS lock is very very quick. Let’s hope BEVRC give us an antenna tracker to go with it next.

 CEOSD, February 1, 2011

great product and great value for money. Simple effective small and light. Great service too. I had one of mine going faulty on me but BEVRC replaced it under warranty with no fuss

 CE OSD, January 10, 2011

Just survive my worst FPV disaster ever... Still working...Easy to setup just plug and play...nevest version don\'t have screen with plane on,looks like on video above.Great product... my crash video:. with CE OSD http://vimeo.com/18468355

 Nickos, December 9, 2010

Have several flights with this osd. like it very much, simple to instal and realy enjoyable to fly with!! super !!!

 Easy setup, November 3, 2010

This is my first Osd & I am very happy with it, the setup was easy and no configuration required! would recommend to anyone

 , August 17, 2010

Great value, works well, small and light unit.